1. Change the lawn mower carburetor filter.
Your lawn mower’s air filter guards the carburetor and engine from debris like grass clippings and dirt. When the air filter becomes clogged or too dirty, it can prevent the engine from starting. To keep this from happening, replace paper filters—or clean or replace foam filters—after every 25 hours of engine use.
The process for removing the filter depends on whether you are operating a riding or walk-behind lawn mower. For a riding mower, turn off the engine and engage the parking brake; for a walk-behind mower, pull the spark plug wire from the plug. Then, lift the filter from its housing.
The only choice for paper filters is replacement. If you’re cleaning a foam filter, wash it in a solution of hot water and detergent to loosen grime. Allow it to dry completely, and then wipe fresh motor oil over the filter, replace it in its housing, and power up the mower—this time to the pleasant whirring of an engine in tip-top condition.
2. Check the spark plug.
Is your lawn mower still being stubborn? The culprit may be the spark plug, which is responsible for creating the spark that ignites the fuel in the engine. If it’s loosened, disconnected, or coated in water or carbon residue, the spark plug may be the cause of your machine’s malfunction.
Locate the spark plug, often found on the front of the mower, and disconnect the spark plug wire, revealing the plug beneath. Use a socket wrench to unscrew the spark plug and remove it.
Check the electrode and insulator. If you see buildup, spray brake cleaner onto the plug, and let it soak for several minutes before wiping it with a clean cloth. Reinstall the spark plug, first by hand, and then with a socket wrench for a final tightening. If the problem persists, consider changing the spark plug.
3. Clear the mower deck of debris.
The mower’s deck prevents grass clippings from showering into the air like confetti, but it also creates a place for them to collect. Grass clippings can clog the mower deck, especially while mowing a wet lawn, preventing the blade from turning.
If the starter rope seems stuck or is difficult to pull, then it’s probably due to a clogged deck. With the mower safely turned off, tip it over onto its side and examine the underbelly. If there are large clumps of cut grass caught between the blade and deck, use a trowel to scrape these clippings free. When the deck is clean again, set the mower back on its feet and start it up.
4. Clear the vent in the lawn mower fuel cap.
The mower started just fine, you’ve made the first few passes, then all of a sudden the mower quits. You pull the cord a few times, but the engine just sputters and dies. What’s happening? It could have something to do with the fuel cap. Most mowers have a vented fuel cap. This vent is intended to release pressure, allowing fuel to flow from the tank to the carburetor. Without the vent, the gas fumes inside the tank begin to build up, creating a vacuum that eventually becomes so strong that it stops the flow of fuel.
5. Clean and refill the lawn mower fuel tank.
An obvious—and often overlooked—reason your mower may not be starting is that the tank is empty or contains gas that is either old or contaminated with excess moisture and dirt. If your gas is more than a month old, use an oil siphon pump to drain it from the tank.
(It’s important to be careful as spilled oil can cause smoking, but there are other reasons this might happen.
6. Add fuel stabilizer to the tank.
Fill the tank with fresh fuel and a fuel stabilizer to extend the life of the gas and prevent future buildup. A clogged fuel filter is another possible reason for a lawn mower not to start. When the filter is clogged, the engine can’t access the gas that makes the system go. If your mower has a fuel filter (not all do), check to make sure it’s functioning properly.
7. Inspect the safety release mechanism cable.
Your lawn mower’s reluctance to start may have nothing to do with the engine at all but rather with one of the mower’s safety features: the dead man’s control. This colorfully named safety bar must be held in place by the operator for the engine to start or run. When the bar is released, the engine stops. While this mechanism cuts down on the likelihood of horrific lawn mower accidents, it also can be the reason the mower won’t start.
The safety bar of a dead man’s control is attached to a metal cable that connects to the engine’s ignition coil, which is responsible for sending current to the spark plug. If your lawn mower’s engine won’t start, check to see if that cable is damaged or broken. If it is, you’ll need to replace it before the mower will start.
Fortunately, replacing a broken control cable is an easy job. You may, however, have to wait a few days to get the part. Jot down the serial number of your lawn mower, then head to the manufacturer’s website to order a new cable.
8. Check to see if the flywheel brake is fully engaged.
The flywheel helps to make the engine work smoothly through inertia. When it isn’t working properly, it will prevent the mower’s engine from working.
If it is fully engaged, it can make a mower’s pull cord hard to pull. Check the brake pad to see if it makes full contact with the flywheel and that there isn’t anything jamming the blade so the control lever can move freely.
If the flywheel brake’s key sheared, the mower may have run over something that got tangled in the blade. It is possible to replace a flywheel key, but it does require taking apart the mower.
9. Look out for signs that the mower needs professional repairs.
While repairing lawn mowers can be a DIY job, there are times when it can be best to ask a professional to help repair a lawn mower. If you’ve done all of the proper mower maintenance that is recommended by the manufacturer, and gone through all of the possible ways to fix the mower from the steps above, then it may be best to call a pro. Here are a few signs that indicate when a pro’s help is a good idea.
You see black smoke. The engine will benefit from a technician’s evaluation, as it could be cracked or something else might be worn out.
Excessive oil or gas usage. If you’ve changed the spark plugs, and done all of the other maintenance tasks, and the mower is consuming more than its usual amount of oil or gas, consult a professional for an evaluation.
The lawn mower is making a knocking sound. When a lawn mower starts making a knocking sound, something could be bent or out of alignment. It may be tough to figure this out on your own, so a pro could help.
A vibrating or shaking lawn mower can be a sign of a problem beyond a DIY fix. Usually something is loose or not aligning properly.
